Categories
BLOG

starburst bowl weed

How to make a Starburst weed pipe

Just when you think you’ve seen everything, along comes the Starburst weed pipe, a delicious addition to any DIY project collection. If you ever find yourself without a bong, pipe or rolling papers, then this handy cannabis enthusiast hack might come in handy. Even if you don’t, the process of creating this masterpiece weed pipe is so much fun that you will have the urge to show your friends again and again. The best part is, these lovable candies are so full of flavor that they can improve the taste of any mediocre product.

How to make a homemade pipe with Starburst

If this sounds like the perfect project for you, then keep on scrolling to learn exactly how to make a Starburst (or any other soft candy) weed pipe for less than one dollar and in under 10 minutes.

  • 1 full-sized pack of Starburst (any flavor)
  • 1 screwdriver
  • 1 screen (optional)

Begin by unwrapping 14 pieces of Starburst candies pieces.

Next, take a screwdriver and slowly feed each piece onto the metal rod just like you would prepare a skewer for dinner. Technically, you can make your homemade weed pipe any size that you’d like, but experience shows that 7 pieces make a good base for your first chamber.

Once all the pieces have been pierced, apply a small amount of pressure to fuse them all together. Starburst candies are quite sticky, so you shouldn’t need water or any other messy materials to make that happen. When they stick together, it should be relatively easy to pull the entire row of candy off the screwdriver in one piece.

The next step is making an elbow joint, that will connect the weed pipe base to the bowl. To do this, take one piece of Starburst and piece it just like you did with the other, but then remove it and poke an additional hole in one of the smaller edges that meets the one in the middle, try not to go past it.

Press the new elbow onto the rest of the weed pipe base until it sits firmly in place.

The next step is the candy bowl, which consists of two pieces of Starburst that are fused together. Use the screwdriver to poke a hole through the center, then tilt it on an angle to gently shape the top opening into the perfect bowl shape.

Install the candy bowl by lining up the holes and gently applying a small amount of pressure.

You are almost done, and all that’s left is sealing off the long chamber in your weed pipe so that you can draw from the device. Though some might prefer to leave it alone and use the addition as a carb, the easiest way is to seal it off with one final unaltered Starburst candy.

Shape and install a fine mesh screen with pressure and your homemade weed pipe is ready to go.

Candy flavored marijuana strains

Though all types of weed will taste incredible through a Starburstweed pipe, the best ones are going to come along with a sweet candy flavor that compliments the traditional taste of a Starburst. Below, we’ ve listed 10 delicious weed strains that are perfect for all smoking pipes, but even better when combined with the fruity flavors of a Starburst candy.

Just when you think you’ve seen everything, along comes the Starburst weed pipe, a delicious addition to any DIY project collection.

How to Make a Better Starburst Pipe

Welcome to our step-by-step guide on how to make a Starburst Pipe. Perhaps you’ve already tried the apple pipe, and you’re looking for something different. Follow these steps to make a fun edible bowl.

**Important**– It has come to my attention that smoking sugar has increased risk of lung-related health problems. I did not experience any problems after trying this out, however, I no longer recommend making starburst pipes. I will leave this article intact for transparency.

Step 1: Unwrap the Starburst. You may want to hold on the a few of the wrappers. They make your candy pipe easier to hold, and keeps your hands from getting sticky.

Step 2: Mold your pipe. The easy way to this is to simply stack them together and squish them until they are adequately bonded together. Another methods is to completely mix all the starburst together into one large mass. From there you can mold the candy into whatever shape pipe you would like.

Step 3: Use a skewer (or something like it) to create a hold through the shaft of your pipe. You may want to line up the skewer on the outside of the pipe so you know exactly how deep the hole should be.

Step 4: Maneuver the skewer around at an angle to create a bowl.

Step 5: (optional) At this point you may want to put it in the refrigerator for a couple of minutes. It may have gotten too soft as you were manipulating it.

Step 6: You’re ready to smoke your new Starburst pipe. Consider holding it with the wrapper so you don’t get sticky. Don’t forget to puff puff pass.

Bonus: Chocolate Bar Pipe

After trying starburst for pipe making, I wanted to see how far I could go with the candy pipe. I picked up a 3 Musketeers bar, and decided to give it a shot. I knew this wasn’t going to be an ideal pipe, but I wanted to see if it would at least work. I made the pipe using pretty much the same method shown above.

How did it work? Actually, it worked better than I had anticipated. Don’t get me wrong – my hands and lips got covered in chocolate, but I was able to burn a decent size bowl out of it before it stopped hitting. I wouldn’t recommend this as a go-to pipe solution, but if it’s all you got then it will work.

Go on! Give it a try, and let me know how it worked out in the comments.

Welcome to our step-by-step guide on how to make a candy Starburst Pipe. Follow these instructions to make an easy, fun, and edible bowl. ]]>